Nuovo ordine Telemetria e OSD per APM 2.6

 

RC FPV Skid Undercarriage Landing Gear Kits Set for DJI F550 450
USD$ 23,99 - EURO 17.71

[gallery ids="737,739,740,741,738"]

---

 

433Mhz Single TTL 3D Robotics 3DR Radio Telemetry Kit for APM APM2 - Blue + Green
USD$ 40,55 - Euro 29.94

[gallery ids="742,743,744"]

Descrizione dal sito: 

The 3DR Radio telemetry system is designed as an open source Xbee replacement radio set, offering a lower price, longer range and superior performance to Xbee radios. It's available in 915MHz; and in the following configurations: serial board (for the air) and USB (for the ground); The radio is a 2-way half-duplex wireless communication system with a standard TTL UART interface, based on HopeRF's HM-TRP data link modules, and custom firmware that improves upon the modules' original features and performance; The SiK firmware includes a bootloader that permits radio firmware upgrades over the serial interface, and radio firmware with configurable parameters. Firmware upgrades and configuration are fully supported in the APM Mission Planner. Configuration is also possible through AT commands; The item not support Win 7, please consider before buying; 3DR Telemetry Kit Specifications: Air module size:17 x 45mm (without antenna); Ground module size:17 x 69mm (without antenna); Air module Weight: 16.4g (include cable and antenna); Ground module Weight: 16.8g (include antenna); 433MHz; Receiver sensitivity to -121dBm; Transmit power up to 20dBm (100mW); Transparent serial link; Air data rates up to 250kbps; MAVLink protocol framing and status reporting; Frequency hopping spread spectrum (FHSS); Adaptive time division multiplexing (TDM); Supports for LBT and AFA; Configurable duty cycle; Built in error correcting code (can correct up to 25% data bit errors); Demonstrated range of several kilometers with a small omni antenna; Can be used with a bi-directional amplifier for even more range; Open source firmware; AT commands for radio configuration; RT commands for remote radio configuration; Adaptive flow control when used with APM; Based on HM-TRP radio modules, with Si1000 8051 micro-controller and Si4432 radio module; Please note that it is up to you to make sure you are allowed to use these radio modules in your country; These devices can be used as short range licence expemp devices the UK under ESTI EN300 220, please refer to Ofcom IR2030 document, page 17. You will need to configure the device to comply with your countries regulations;

3DR official instructions:

https://code.google.com/p/arducopter/wiki/APM13DRadio?wl=en

Special setting tool:

http://vps.oborne.me/3drradioconfig.zip

Official PCB and schematic diagram:

http://stuff.storediydrones.com/3DR-Radio.zip

http://stuff.storediydrones.com/3DR-Radio-USB.zip

 

---

 

On-Screen Display APM OSD MinimOSD ARDUPILOT MEGA OSD APM2.0 APM2.5 - Purple
USD$ 24,51 - Euro 18,10

[gallery ids="745,746,747"]

Descrizione dal sito: 

MinimOSD is a super-tiny board designed by 3DRobotics. It's all you need to get OSD telemetry data from ArduPilot Mega. Just connect your FPV camera and a video link and you're ready to fly with instruments on screen. It's intended to be a dedicated APM telemetry video output. So, it reads MAVLink messages from its RX and request rates from APM if you connect its TX to ArduPilot "telem" port. Important note: You cannot connect the OSD when your APM 2 is also connected via USB (they share the same port).Make sure you disconnect your USB cable from the APM 2 board before attempting to use the OSD. Details It has the Max7456 chip powered by two stages to avoid noises from servos attached to ArduPilot Mega board.

It provides an extra clean power line to feed the FPV camera and video link. The approach is to use two external power sources: 12V from a Lipo Battery and 5V from APM: Raw 12V from Lipo Battery: Feeds directly FPV camera and video transmitter.

It also feeds Max7456's analog line (AVDD and AGND) by a 5V voltage regulator (avoiding noises from servos attached to APM).

5V from APM telem port: Feeds the ATmega 328P and Max7456's digital line (DVDD and DGND); Note: Optionally, you can use two solder jumps to "tie" digital and analog lines. MinimOSD has no extra pins exposed, because the concept is "capturing all the needed data from MAVLink".

E.g.: to show RSSI from RC receiver, that info needs to be on msgs #35 and #36 (RC_CHANNELS "RAW" and "SCALED").

So, the analog reading of RSSI output from receiver needs to be done on APM analog ports and treated inside the APM code. PAL vs NTSC The format of the video does have an impact on how many characters the OSD can fit on the video feed. The MimimOSD can be configured by the ArduCAM OSD Config Tool to work at PAL or NTSC. The "PAL" solder jumper underneath the board is not used anymore (Firmware 2.0 or above).

---

 

New APM OSD 90A Voltage / Current Sensor Connector Power Module - Black + Red
USD$ 10,75 - Euro 7,93

[gallery ids="748,749,750"]

Descrizione dal sito: 

Support Max. 90A measurement. 3A UEBC output. Length of cable: 25cm

---

Glass Fiber Flight Controller Anti-vibration Set/Shock Absorber for APM2.5/2.6 /KK /MWC

USD$ 5,50 - Euro 4,06

[gallery ids="751"]

Descrizione dal sito: 

Material: glass fiber Suitable for different open source flight controller, such as APM2.5, 2.6, KK, MWC etc.